My title

760.738.4084

Performance Clutch Pin – Grooved

Performance Clutch Pin – Grooved
X

Part Number: AGA-CPP-223-328
Price: $29.00
$29.00
  • The BMW factory pin is made from plastic which has very little heat resistance, which causes premature wear on the pin.
  • All German Auto has reproduced this part to factory from a sturdy silicon bronze, making it heat resistant and durable.
  • The AGA Performance Grooved Clutch Pivot Pin saves customers from having to do frequent, costly repairs by providing a life-long solution to factory parts.
Downloadable PDFs

Models This Product Fits

    525i M50 E34 525i, Wagon E39 525Xi E60 X3 xDrive30i E83 335Xi E90
    530i (V8) E34 530i E39 530Xi E60 Mroadster S54 E85 M3 Sedan E90
    325is E34 540i E39 550i E60 Z4 2.5i, 3.0i/si E85 328i xDrive Wagon, Coupe E91
    318i, ti, is, iC E34 528i, Wagon E39 M5 E60 Z4 3.0si Coupe E86 325Xi Wagon E91
    328i, is, iC E34 323i,Ci/Conv., Wagon E46 528i, Xi, ixDrive E60 Mcoupe S54 E86 328i, Xi Wagon E91
    M3 B30 E34 328i, Ci E46 535i, Xi E60 128i Conv. E88 328i, Xi Coupe E92
    M3 B32 E34 330i, Ci, Xi, Ci Conv. E46 530Xi Wagon E61 135i Conv. E88 335i Coupe/ xDrive Coupe E92
    323is, iC E34 325i, Xi, Ci, Ci Conv. E46 535i xDrive Wagon E61 Z4 sDrive 30i E89 M3 Coupe E92
    M Roadster S54 Z3 325i/Xi Wagon E46 645Ci, Ci Conv. E64 325i, Xi E90 335Xi Coupe E92
    M Coupe S54 Z3 M3, M3 Conv. E46 650i, Conv. E64 330i, Xi E90 328i Conv. E93
    MRoadster S52 Z3 525i N52 E60 M6 Conv. E64 328i, Xi E90 335i Conv. E93
    Mcoupe S52 Z3 545i E60 128i & 135 E82 335i E90 M3 Conv. E93
    Z3 1.9, 2.3, 2.5i, 2.8 Z3 525i M54 E60 135i E82 328i xDrive E90 X5 3.0i SAV
    Z3 Coupe 2.8, 3.0 Z3 530i M54 E60 X3 2.5i, 3.0i/si E83 335i xDrive E90    

Part Included

Quantity 1
Part # AGA-CPP-223-328
Description Performance Clutch Pin - 328 - Grooved
Total $29.00
1 Review(s)

I purchased 2 of these, one for my E36 M3 and the other for my E39 540i. A very nice little addition to any clutch job, performance or stock replacement.

Write Your Own Review

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Price
Quality
Ease-of-Use

These instructions are for experienced technicians only. This job should only be done by an experienced technician. If instructions are need to remove stock components refer to All Data, Mitchel or Factory Manual.

STEP 1

o install the pin, simply place pin in hole. Place socket that fits over dome without touching the end of pin. 15mm 12 point socket works well for this. Lightly tap socket with extension until the pin is fully seated. It is normal for the pin to fit tight. DO NOT hit end of pin with a hammer, punch extension, etc